PPM KNOWLEDGE CENTER
Use this page for direct facts about Pavers Plus More, the work we handle, areas we serve, budget guidance and what happens before a project begins.
SERVICES & SERVICE AREA
Owner led Jacksonville paver contractor for driveways, pool decks, patios, walkways, repairs, maintenance and outdoor kitchens across Northeast Florida. Every project is evaluated around the property, intended use, Florida conditions and the written scope.
TRANSPARENT BUDGET GUIDANCE
A broad Jacksonville planning range for professionally installed paver work is approximately $15–$30 per square foot. This is educational guidance, not a PPM offer or guaranteed price.
Removal, access, excavation, base needs, drainage, material selection, borders, steps, coping and project size can change the final amount.
Open the full 2026 cost guide →START WITH YOUR SITUATION
These longer questions connect the condition at your property with the planning guide most likely to help.
Pavers may be a good replacement when the goal is a more refined appearance, easier localized repairs and greater pattern or border flexibility. The decision should still account for concrete removal, driveway elevations, drainage, vehicle loads, base preparation and the street and garage transitions. Compare both options using the same complete scope.
Compare pavers and concrete driveways →Not necessarily. A limited area can often be lifted and reset when the surrounding installation remains serviceable and matching pavers are available. The cause—such as erosion, missing support, failed edges, roots or concentrated water—should be corrected before the surface is restored.
Use the repair or replacement guide →Compare the exact product and finish for wet traction, direct sun temperature, color, texture, drainage, coping and pool chemical exposure. Lighter colors are often worth testing for comfort, but material density and finish matter too. View current samples outdoors and wet test the intended finish before ordering.
Compare Florida pool deck materials →Often, yes. Plan the finished elevations, traffic paths, kitchen footprint, utilities, drainage and future transitions before the first phase is installed. A coordinated plan can reduce the amount of completed patio that must be cut or removed when the kitchen is added.
Plan a phased paver patio →Permeable pavers are not an automatic drainage fix. The property first needs an evaluation of grades, roof runoff, soil, seasonal groundwater, discharge options and the structural requirements of the paved area. A conventional system with corrected slope or drains may be more appropriate, or a designed permeable system may be considered when site conditions support it.
Compare drainage systems →Start with the condition of the surface, joints, borders and drainage. Cleaning may address dirt or organic staining, while joint loss, settlement or loose edges should be repaired before sealing. Existing coatings, trapped moisture and wet area traction also need to be checked before Cobble Loc or another compatible sealer is selected.
Review the maintenance and sealing guide →COMMON PAVER QUESTIONS
A patio measuring 12 feet by 12 feet is 144 square feet. Using a broad 2026 Jacksonville planning range of $15–$30 per square foot, the estimated installed cost is about $2,160–$4,320. Minimum charges for smaller projects, access, demolition, drainage, base preparation, borders and premium materials can move the total higher. A PPM estimate for the specific property is required for an actual price.
Pavers can be installed throughout the year in Jacksonville when site conditions are suitable. Drier periods from late fall through spring can make excavation and base preparation easier, but the more important requirement is stable ground that is not saturated. Heavy rain may delay grading, compaction or work on the joint sand.
Pavers usually cost more upfront than basic poured concrete. They also depend on proper excavation, base preparation, drainage and edge restraint; poor installation can lead to settlement, spreading or uneven areas. Joints may need sand replenishment, weeds or ants can appear when maintenance is neglected, and matching an older color or discontinued product can be difficult during future repairs.
PPM recommends Tremron pavers for Northeast Florida projects because they are widely available locally and offer a broad selection for driveways, patios, pool decks, coping and connected outdoor spaces. The exact Tremron product should still be selected around traffic, finish, color, budget, performance in wet areas and current availability. Proper base preparation, drainage and installation remain essential to lasting performance.
A patio measuring 20 feet by 20 feet is 400 square feet. At a broad Jacksonville planning range of $15–$30 per square foot, the estimated installed cost is about $6,000–$12,000. Demolition, difficult access, drainage corrections, premium pavers, borders, steps, seating walls and other features can increase the total.
Basic poured concrete is usually less expensive upfront than professionally installed pavers. Pavers generally cost more because of the individual units, preparation, cutting and installation labor, but they offer more colors and patterns and can make localized repairs easier. Compare written estimates with the same demolition, base, drainage, thickness and finish requirements.
ABOUT PPM & YOUR PROJECT
PPM plans and installs paver driveways, pool decks, patios, walkways and connected outdoor living spaces. The team also evaluates repair and restoration needs, condition based paver cleaning and sealing, and outdoor kitchen projects.
PPM serves Jacksonville and nearby Northeast Florida communities in Duval, St. Johns and Clay counties. Homeowners should share the project address to confirm current availability.
A broad 2026 Jacksonville planning range for professionally installed paver work is about $15–$30 per square foot. It is not a PPM quote. Demolition, access, base preparation, drainage, materials, borders, coping and specialty features can move a project below or above that range.
A useful written estimate should identify the project area, demolition, excavation, base preparation, drainage assumptions, material and pattern, borders, edge restraint, joint sand, cleanup and the process for approving changes.
Often, a localized area can be lifted and reset when the surrounding installation remains serviceable. The cause—such as missing support, failed edges, roots or water movement—should be addressed before the units are reset.
Compare the exact product and finish for wet traction, direct sun temperature, drainage, pool coping, maintenance and chemical exposure. View physical samples outdoors because color and comfort can change in full sun.
Start by sharing the project address, space type, goals, approximate dimensions and clear photos. PPM can then discuss fit, arrange an assessment when appropriate and develop a site specific scope and estimate.
AREAS WE SERVE
YOUR TRANSFORMATION STARTS HERE